Search Results

The first commercially available plug-in hybrid electric vehicle (PHEV), the General Motors (GM) Volt, was introduced into the market in mid-December 2010. The Volt uses a series-split powertrain architecture, which provides benefits over the series architecture that typically has been considered for use in electric-range extended vehicles (EREVs). A specialized EREV powertrain, called the Voltec, drives the Volt through its entire range of speed and acceleration with battery power alone and within the limit of battery energy, thereby displacing more fuel with electricity than a PHEV, which characteristically blends electric and engine power together during driving. This paper assesses the benefits and drawbacks of these two different plug-in hybrid electric architectures (series versus series-split) by comparing component sizes, system efficiency, and fuel consumption over urban and highway drive cycles.

The presentation by Tucker Perkins, President of CleanFUEL USA, provides important information to those wanting to learn about alternative fuels, specifically propane autogas. CleanFUEL USA provides liquid propane injection engine system for the 6L engine in the GM G4500 cutaway chassis used in many Type A busses. They are also developing an 8L engine in partnership with Freightliner/ThomasBuilt Bus for the Type C bus. This presentation discussed many of the advantages of propane autogas use, such as better economics, lower emissions, and inexpensive infrastructure for the fueling network. Presenter Tucker Perkins, CleanFUEL USA

Who are the people who know the most about the buses in your fleet? They are most likely the operators and the servicing technicians. They are also the key people whose knowledge, level of training and attitude can determine the success or failure of new powertrain technologies. Training and recruitment of both need to be held to a higher standard than we have seen in the past. I will argue that even the culture of those involved in fleet operations needs to be changed. The bar for technical competence and product knowledge needs to be raised for operators and technicians. In return managers should find ways to include them as stakeholders, investing them with both additional responsibility and accountability. This will require greater access to training and recognition of achievement. Where are the busses stored and serviced? Most likely in an all-purpose state/county/municipal service facility servicing a variety of equipment.

Understanding the different types of alternative fuel and advanced vehicle technologies that are available, and deciding which would be the best fit for your fleet, is only half the battle. Limited budgets, now more than ever, create a need to find funding assistance to pursue these new technologies. This presentation will provide insight into making sure you know what assistance is available by providing information not only on the funding programs themselves, but also who to know and where to go to make sure you always have access to the best available information. Presenter Lori Clark, North Central Texas Council of Gov

A review of the processes that lead to the conclusion that CNG was the best solution for the fleet, including the efforts to gain public support for alternative fuels for school buses. MISD is now home for 42 CNG powered school buses (of 200). The presentation will include training and design tips for safety and smooth operations along with maintenance considerations for using CNG. Alternative fuels, the dilemma of which comes first - refueling station or operational buses ? has an impact on grant approval and funding, bearing discussion of the option of a public/private model. Unlike other alternative fuels, CNG has a national security impact Presenter Charles Stone, Mansfield Indep School Dist

With so many options for alternative fuels, advanced vehicles, and emission reduction technologies, how can fleet managers make the best decisions for their fleet?s performance, compliance, and sustainability goals? Even more important, where is the funding that is often critical for implementing these decisions? This presentation will provide guidance on how to assess the options, how to prepare for writing grants and where to find funding opportunities. Presenter Laura Palombi, Clean Energy Coalition

The development of PM and NOx reduction system with the combination of DOC included DPF and SCR catalyst in addition to the AOC sub-assembly for NH3 slip protection is described. DPF regeneration strategy and manual regeneration functionality are introduced with using ITH, HCI device on the EUI based EGR, VGT 12.3L diesel engine at the CVS full dilution tunnel test bench. With this system, PM and NOx emission regulation for JPNL was satisfied and DPF regeneration process under steady state condition and transient condition (JE05 mode) were successfully fulfilled. Manual regeneration process was also confirmed and HCI control strategy was validated against the heat loss during transient regeneration mode. Presenter Seung-il Moon

This paper presents the first results of an experimental study into a hybrid combustion concept for next-generation heavy-duty diesel engines. In this hybrid concept, at low load operating conditions, the engine is run in Pre-mixed Charge Compression Ignition (PCCI) mode, whereas at high load conventional CI combustion is applied. This study was done with standard diesel fuel on a flexible multi-cylinder heavy-duty test platform. This platform is based on a 12.9 liter, 390 kW heavy-duty diesel engine that is equipped with a combination of a supercharger, a two-stage turbocharging system and low-pressure and high-pressure EGR circuitry. Furthermore, Variable Valve Actuation (VVA) hardware is installed to have sufficient control authority. Dedicated pistons, injector nozzles and VVA cam were selected to enable PCCI combustion for a late DI injection strategy, free of wall-wetting problems.

Historically, the opposed-piston, two-stroke (OP2S) diesel engine set combined records for fuel efficiency and power density that have yet to be met by any other engine type. However, with modern emissions standards, wide-spread development of this engine for on-highway use stopped. At Achates Power, state-of-the-art analytical tools and engineering methods have produced an OP2S engine that, when compared to a leading medium-duty engine, has demonstrated a 21% fuel efficiency gain and engine-out emissions levels meeting U.S. EPA10 with conventional after-treatment. Among the presentation topics covered are thermodynamic efficiency, demonstrated engine results, cost and weight advantages, and overcoming two-stroke engine challenges. Presenter David Johnson, Achates Power Inc.

Ford's EcoBoost GTDI engine technology (Gasoline Direct Injection, Turbo-charging and Downsizing) is being successfully implemented in the market place with the EcoBoost option accounting for significant volumes in vehicle lines as diverse as the F150 pickup truck, Edge CUV and the Lincoln MKS luxury sedan. A logical question would be what comes after GTDI? This presentation will review some of the technologies that will be required for further improvements in CO2, efficiency and performance building on the EcoBoost foundation as well as some of the challenges inherent in the new technologies and approaches. Presenter Eric W. Curtis, Ford Motor Co.

In this presentation, we will explain how the traditional Miller Cycle - which has its limitations in the traditional four-stroke, Otto Cycle engine provides new opportunities for greater fuel efficiency gains and engine downsizing when incorporated in a split-cycle combustion process. Results will also be shared from studies showing how these implementations can provide both significant drops in fuel consumption and increases in power when incorporated into some of today's most economic vehicles. Presenter Stephen Scuderi, Scuderi Group LLC

Future fuel economy targets represent a significant challenge to the automotive industry. While a range of technologies are in research and development to address this challenge, they all bring additional cost and complexity to future products. The most cost effective solutions are likely to be combinations of technologies that in isolation might have limited advantages but in a systems approach can offer complementary benefits. This presentation describes work carried out at Ricardo to explore Intelligent Electrification and the use of Stratified Charge Lean Combustion in a spark ignition engine. This includes a next generation Spray Guided Direct Injection SI engine combustion system operating robustly with highly stratified dilute mixtures and capable of close to 40% thermal efficiency with very low engine-out NOx emissions.

Turbulent Jet Ignition is an advanced spark initiated pre-chamber combustion system for otherwise standard spark ignition engines. Combustion in the main chamber is initiated by jets of partially combusted (reacting) pre-chamber products which provide a high energy ignition source. The resultant widely distributed ignition sites allow relatively small flame travel distances enabling short combustion durations and high burn rates. This presentation outlines development of this combustion concept in a modern normally aspirated PFI production engine. Experimental results have highlighted high thermal efficiency (42.8%), significant fuel economy improvement (>20%), low engine out NOx (<10 ppm), knock limit extension, high load capability (>13 bar IMEPn) and high speed operation (5500 rev/min). Presenter William P Attard, MAHLE Powertrain LLC

The Renewable Fuels subscription provides unlimited access to SAE Technical Papers covering global applied research, development and applications regarding renewable fuels. This resource chronicles developments in biofuels, ethanol, methanol, biodiesel, and hydrogen fuels, which are increasing in production and use globally. The more than 2,000 papers in this resource cover: Petrol-Ethanol Blends Diesel Engines with Biofuels Renewable Oxygenated Fuels Biogasoline Options Flex Fueled Engines Methanol-Air and Ethanol-Air Mixtures

This technical paper collection contains 30 papers that detail transmissions and drivelines. Topics covered include: simulation/modeling, components/subsystems, controls, all wheel drive/ NVH/launch devices, hybrid powertrain concepts, and transmission systems/drive units.

This technical paper collection contains 17 papers that cover emission and combustion characteristics, development of DME engine, biodiesel fuels, and opposed piston opposed cylinder (OPOC) engine performance development.

This technical paper collection contains 20 papers detailing CI engine performance using alternative fuels and diesel engines and components.

Focusing on the effects of alternative fuels in compression ignition engines this technical paper collection contains 21 papers. Topics covered include hydrogen, ethanol, methane, biodiesel and synthetic diesel fuel. Data pertaining to emissions reduction, performance, combustion analysis, efficiency, and durability for both experimental as well as numerical investigations is also covered.

The 18 papers in this technical paper collection focus on alternative fuels in a general context. Topics covered include: the use of alternative fuels for SI engine application; the application of oxygenated fuels for CI engine application; the development and understanding of surrogate and reference fuels; plus other alternative and advanced fuels concepts for current and future engine technologies.

This technical paper collection contains 53 technical papers. Topics covered include engine exhaust aftertreatment and integration; hybrid vehicle integration and optimization; powertrain and drivetrain NVH; advanced transmission and driveline component design; diesel engine system design; fuel economy; alternative fuels; and advanced engine component design.